陜西三面169厚度的防爆墻廠家設計施工 價格合理

聯系人：鄭經理

電話：16632856788

衡水恒綽建筑工程有限公司位于河北省衡水市桃城區，擁有多年從事防爆門窗,泄 爆門窗以及隧道防護門設計、開發和銷售的業務骨干，專業的防爆墻、抗爆墻、泄爆墻設計、安裝施工技術人 員及施工團隊。公司技術力量雄厚，是一家集生產、加工、制造為一體的企業。
公司主營業務及產品：
防爆墻抗爆墻設計、安裝、施工、維護、更換等；
泄爆墻設計、安裝、施工、維護、更換等；
隧道防護門的設計、生產、安裝、維修；
防爆門窗的設計、生產、安裝、維修；
泄爆門窗的設計、生產、安裝、維修；

有很多業主詢問“輕鋼龍骨隔墻如何安裝”，輕鋼龍骨隔墻是常見的一種隔墻材質，不過輕鋼龍骨隔墻安裝方法比較復雜，那么輕鋼龍骨隔墻安裝圖解是什么？輕鋼龍骨隔墻安裝步驟有哪些？下面帶來輕鋼龍骨隔墻安裝方法介紹。

步驟1：墻位放線

根據設計圖紙確定的隔斷墻位，在樓地面彈線，并將線引測至頂棚和側墻

步驟2：踢腳臺施工

如設計要求設置踢腳臺（墻墊）時，應先對樓地面基層進行清理，并涂刷YJ302型界面處理劑一道，然后澆筑C20素混凝土踢腳臺，上表面應平整，兩側面應垂直，踢腳臺內是否配置構造鋼筋或埋設預埋件，根據設計要求確定。

步驟3：安裝沿地、沿頂沿邊龍骨

橫龍骨與建筑頂、地連接及豎龍骨與墻、柱連接，一般可用，選用M5*35的釘將龍骨與混凝土基體固定，對于磚砌墻、柱體應采用金屬脹螺栓，**或電鉆打孔時，固定點的間距通常按900mm布置，大不應超過1000mm，輕鋼龍骨與建筑基體表面接觸處，一般要求在龍骨接觸面的兩邊各粘貼一根通長的橡膠密封條，以起防水和隔聲作用，沿地、沿頂和靠墻（柱）龍骨的固定方法。

步驟4：安裝豎龍骨

豎龍骨按設計確定的間距就位，通常根據罩面板的寬度尺寸而定，對于罩面板材較寬者，需在其中間加設一根豎龍骨，豎龍骨中距大不應超過600mm，對于隔斷墻的罩面層較重時（如貼瓷磚）的豎龍骨中距，應以不大于420mm為宜，當隔斷墻體的高度較大時，其豎龍骨布置也應加密。

豎龍骨安裝時應由隔斷墻的一端開始排列，設有門窗者要從門窗洞口開始分別向兩側展開，當后一根豎龍骨距離沿墻（柱）龍骨的尺寸大于設計規定的龍骨中距時，必須增設一根豎龍骨，將預先截好長度的豎龍骨推向沿頂、沿地龍骨之間，翼緣朝罩面板方向就位，龍骨的上、下端如為剛柱連接，均用自攻螺釘或抽心鉚釘與橫龍骨固定，應注意當采用有沖孔的豎龍骨時，其上下方向不能顛倒，豎龍骨現場截斷時一律從其上端切割，并應保證各條龍骨的貫通孔高度必須在同一水平。

門窗洞口處的豎龍骨安裝應依照設計要求，采用雙根并用或是扣盒子加強龍骨，如果門的尺度大且門窗較重時，應在門框外的上下左右設置斜撐。

步驟5：安裝通貫龍骨

通貫橫撐龍骨的設置，一種是低于3m的隔斷墻安裝1道;3-5m高度的隔斷墻安裝2-3道，通貫龍骨橫穿各條豎龍骨的貫通沖孔，需要接長時使用其配套的連接件，在豎龍骨開口面安裝卡托或支撐卡與通貫橫撐龍骨連接鎖緊，根據需要在豎龍骨背面可加設角托與通貫龍骨固定，采用支撐卡系列的龍骨時，應先將支撐卡安裝于豎龍骨開口面，卡距為400-600mm，距龍骨兩端的距離為20-25mm。

步驟6：安裝橫撐龍骨

隔斷墻輕鋼骨架的橫向支撐，除采用通貫龍骨外，有的需要設其他橫撐龍骨，一般當隔墻骨架超過3m高度時，應設橫向龍骨對骨架加強，或予以固定板縫，具體做法是，可選用U型橫龍骨或C型豎龍骨作橫向布置，利用卡托、支撐卡（豎龍骨開口面）及角托（豎龍骨背面）與豎向龍骨連接固定，有的系列產品，也可采用其配套的金屬嵌縫條作橫豎龍骨連接固定件。

以上就是關于“輕鋼龍骨隔墻如何安裝 輕鋼龍骨隔墻安裝方法介紹”全部內容，總的來說輕鋼龍骨隔墻安裝步驟還是比較復雜的，大家一定要嚴格按照規范安裝輕鋼龍骨隔墻，這樣才能保證安全性，想知道更多輕鋼龍骨隔墻知識可以戳我>>咨詢。